OYTITHERM PS4515
General-purpose pressure-sensitive hotmelt with balanced tack and cohesion.
Request TDS/SDSLABELS & TAPES
The first touch.
A lasting connection.
Pressure-sensitive hotmelt adhesives for self-adhesive articles. OYTITHERM solutions for tapes, labels and the surfaces they need to bond.
Explore our PSA gradesExplore the three tape constructions using the numbered points.
01
Masking Tape
A conformable paper backing for masking. Balance reliable holding with clean removal from the intended surface.
Explore this tape02
BOPP Tape
A biaxially oriented polypropylene backing for packaging tape. Match rapid wetting and holding power to the carton and closing process.
Explore this tape03
Duct Tape
A reinforced cloth construction for holding, bundling and repair. Balance contact on uneven surfaces with cohesive strength.
Explore this tapeTHE APPLICATION
Balance tack.
Build lasting adhesion.
A self-adhesive article brings a backing, an adhesive layer and an end-use surface together. The right balance of initial tack, adhesion and internal strength depends on the complete construction and the conditions in which it will be used.
OYTITHERM / PRESSURE-SENSITIVE HOTMELTS
Six grades.
Made for lasting contact.
Explore our pressure-sensitive hotmelts for self-adhesive labels and tapes. Discuss your backing, surface and coating process with our team to select the right grade.
OYTITHERM PS4540
An economical, high-tack pressure-sensitive hotmelt for self-adhesive labels.
Request TDS/SDSOYTITHERM PS4516
High-tack pressure-sensitive hotmelt for low-temperature bonding.
Request TDS/SDSOYTITHERM PS4650
Colourless, general-purpose pressure-sensitive hotmelt.
Request TDS/SDSOYTITHERM PS4598
General-purpose pressure-sensitive hotmelt for self-adhesive articles.
Request TDS/SDSOYTITHERM PS4503.1
High-performance pressure-sensitive hotmelt with high tack for high-temperature applications.
Request TDS/SDSRequest the current TDS and SDS for grade-specific technical data and handling information. Confirm suitability with your actual backing and production process.
THREE BACKINGS / THREE BONDING BRIEFS
Made for the job.
From masking to sealing.
Masking Tape
Hold accurately. Remove cleanly.
Creped paper helps a masking tape follow gentle curves and tear by hand. The adhesive needs to hold the edge in place during the intended masking operation.
Construction & evaluation
- The construction
- Paper backing, adhesive and a controlled unwind surface.
- What matters
- Edge definition, conformability, dwell time and residue-free removal on the intended substrate.
- Evaluate together
- Peel behaviour after use, adhesive transfer and compatibility with the actual coating or drying cycle.
BOPP Tape
A thin film. A secure closure.
Biaxially oriented polypropylene film provides a lightweight backing for carton-sealing tapes. Synthetic-rubber pressure-sensitive adhesives are one established option for rapid initial adhesion.
Construction & evaluation
- The construction
- BOPP film and PSA, with surface preparation and unwind behaviour matched to the coating process.
- What matters
- Initial grab, holding power and dependable contact with the actual carton surface.
- Evaluate together
- Manual or automatic dispensing, flap spring-back, storage conditions and variation in paperboard.
Duct Tape
Reinforced backing. Flexible contact.
A typical duct tape combines a polyethylene-coated cloth backing with a pressure-sensitive adhesive. The cloth reinforces the tape while allowing practical handling and hand tearing.
Construction & evaluation
- The construction
- Protective outer film, reinforcing fabric and adhesive coating.
- What matters
- Conformability, initial contact on uneven surfaces and resistance to movement under load.
- Evaluate together
- Peel and shear behaviour, backing strength and the moisture or temperature exposure expected in use.
Tape names describe constructions, not a single adhesive chemistry. OYTITHERM hotmelt PSA selection is based on the backing, converting line and intended use.
LABELS / FROM FACTORY TO DELIVERY
Different surfaces.
Different demands.
A label must stay in place and keep its information readable through the journey it was designed for.
TYRE LABELS
Grip a challenging surface.
Curved tread, rough rubber and migrating rubber constituents make tyre labelling demanding. Specialised high-tack adhesives and suitable barrier facestocks address different parts of this challenge.
- Contact and edge lift on the actual tread geometry
- Resistance to staining through the face material
- Adhesive edge bleed during converting and storage
- Appearance and adhesion after the intended handling cycle
Assess the whole label construction on representative tyres, including the intended storage conditions.
COURIER & LOGISTICS LABELS
Keep information moving.
Shipping labels bring the printed face, adhesive and release liner together. Paperboard, coated cartons and plastic mailers present different bonding surfaces.
- Initial tack during fast print-and-apply operations
- Reliable contact with the actual package surface
- Readable print throughout handling and distribution
- Suitable performance in cold or humid shipping areas
Application temperature and service temperature are different: a label applied to a cold parcel must develop contact at that temperature.
Illustrative 3D constructions. Layer separation is exaggerated to make the adhesive interface visible.
OYTITHERM / HOTMELT PSA
The balance
behind the bond.
A strong first touch is one part of performance. The adhesive also needs to suit coating, converting and the finished article.
Principle illustrations · not measured product results
Make the first contact count.
Tack describes bond formation during brief contact. Consider the application pressure, substrate and temperature at the moment the label or tape is applied.
Discuss: initial contact and wetting on the real surface.- How readily the adhesive establishes a bond during brief contact.
- The resistance when the tape or label is pulled away under defined conditions.
- The ability of the adhesive layer to resist movement and internal failure under load.
- Coating uniformity, release, die-cutting and edge ooze must work with the complete construction.
MATCHED TO YOUR PROCESS
Explore the
adhesive solutions.
Start with a product family.
Then select the grade for your application.
HIGH PERFORMANCE HOTMELT ADHESIVES
Elastomer-based pressure-sensitive hotmelts for self-adhesive articles, with grade selection and customised development around your product and process.
Explore OYTITHERMLET’S BUILD THE NEXT BOND.
What are
you making?
Tell us about your materials and your production process. Let’s explore the right adhesive together.
Talk to our teaminfo@oyti-adhesives.com+90 226 400 00 27